# VXLAN Flood and Learn Multicast Data Plane

**URL:** <https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096>\
**Category:** Lessons Discussion\
**Created:** [May 22, 2024, 2:21pm UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096 "2024-05-22T14:21:26Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![ReneMolenaar](https://cdn-forum.networklessons.com/user_avatar/forum.networklessons.com/renemolenaar/32/488_2.png) [@ReneMolenaar](https://forum.networklessons.com/u/ReneMolenaar)\
**Post date:** [May 22, 2024, 2:21pm UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096/1 "2024-05-22T14:21:26Z")

</div>

This topic is to discuss the following lesson:

> **[VXLAN Flood and Learn Multicast Data Plane](https://networklessons.com/vxlan/vxlan-flood-and-learn-multicast-data-plane)**
>
> The VXLAN Flood and Learn Multicast Data Plane lesson explains how to use multicast with the flood and learn behavior on VXLAN networks.

---

<div class="post-metadata">

**Author:** ![amit8009271591](https://cdn-forum.networklessons.com/letter_avatar_proxy/v4/letter/a/eb9ed0/32.png) [@amit8009271591](https://forum.networklessons.com/u/amit8009271591)\
**Post date:** [August 30, 2024, 4:00am UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096/2 "2024-08-30T04:00:13Z")

</div>

Hello Everyone,

What will happen if we will not enable pim on loopback interfaces specially on spine ?

Regards

---

<div class="post-metadata">

**Author:** ![lagapidis](https://cdn-forum.networklessons.com/user_avatar/forum.networklessons.com/lagapidis/32/4949_2.png) [@lagapidis](https://forum.networklessons.com/u/lagapidis)\
**Post date:** [August 31, 2024, 4:53am UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096/3 "2024-08-31T04:53:27Z")

</div>

Hello Amit

Strictly speaking, you don’t need to enable PIM sparse mode on the loopbacks of the devices you are using. However, in the specific topology, Rene has chosen to use the loopback interface of the spine switch **as the address of the RP**. This is typically best practice as you can see from [this lesson here](https://networklessons.com/multicast/multicast-pim-sparse-mode). So for this particular case, if you don’t enable PIM sparse mode on the loopback, it cannot participate as the RP of the topology.

I hope this has been helpful!

Laz

---

<div class="post-metadata">

**Author:** ![Giovanni](https://cdn-forum.networklessons.com/letter_avatar_proxy/v4/letter/g/7ea924/32.png) [@Giovanni](https://forum.networklessons.com/u/Giovanni)\
**Post date:** [February 2, 2025, 8:54pm UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096/4 "2025-02-02T20:54:30Z")

</div>

Hi,

Why we need to specify “ip ospf network point-to-point”?

Thanks

---

<div class="post-metadata">

**Author:** ![ReneMolenaar](https://cdn-forum.networklessons.com/user_avatar/forum.networklessons.com/renemolenaar/32/488_2.png) [@ReneMolenaar](https://forum.networklessons.com/u/ReneMolenaar)\
**Post date:** [February 3, 2025, 4:20pm UTC](https://forum.networklessons.com/t/vxlan-flood-and-learn-multicast-data-plane/48096/5 "2025-02-03T16:20:28Z")

</div>

Technically it would work without.

By default, OSPF uses the broadcast network type on Ethernet interfaces. This means it will do a DR/BDR election.

This isn’t needed because we only have p2p links in between spine and leaf switches. The LSDB will also be smaller.

For a lab in doesn’t matter but for a large spine and leaf topology, it does. Here is some more info:

> **[VXLAN Underlay OSPF](https://networklessons.com/vxlan/vxlan-underlay-ospf)**
>
> OSPF can be used for the VXLAN underlay. This lesson explains the configuration with /31 prefixes and ip unnumbered interfaces.
